The DMM Shield is a 5 1/2 Digit digital multimeter, designed for use with Digilent microcontroller boards and FPGA boards that are equipped with the Arduino shield header, seeCompatible Boards. The shield is built around theHY3131module from Hycon Technology, which is an analog front end DMM dedicated chip. The device has 7 measurements functions (AC/DC Voltage, AC/DC Current, Resistance, Diode, Continuity) and is factory calibrated. It can be used out of the box with the compatible system boards.

It is accessed through a custom SPI interface, using digital IO pins exposed in the DMM Shield connector.

• Full compatibility with Digilent System Boards featuring the Arduino Shield
• Provides 4 banana connectors for measurements(Volts/Ω, COM, mAmps, Amps).
• Floating COM
• AC/DC voltage and current measurements
• Diode, continuity measurement/function
• Resistance measurement
• Supports SPI connection

• Programmable multifunctional switch network
• High-resolution, high-speed ∑-Δ ADCs - for high conversion speed, resolution and accuracy
• Digital RMS circuit - the conversion result is processed by the high-speed calculation of the inner hardware to realize the digital RMS [reference:http://www.hycontek.com/wp-content/uploads/Description-HYCON-EN.pdf]
• Operational amplifier
• Multifunctional comparator
• Peak-Hold measurement circuit - to achieve higher accuracy
• Low-Pass filter - implements a third order LPF
• Supports SPI interface connection

The DMM Shield is hardware compatible with all Digilent boards that use the Arduino Shield connector, however, the libraries and out of box experience are written for the following boards:

• Arty-Z7
• uC32™
• WF32™
• Max32™
• Uno32™
• Arduino Uno
• Arduino Due
• Arduino Mega

The DMMShield can be used with both 3.3V and 5V voltage levels existing on the Arduino boards.

Note: The pic32 library is written to target theuC32微控制器。对于所有其他董事会from the series, the pin-out might suffer modifications.

• Accuracy: +/-0.1% on Voltage, Current and 500Ω-5MΩ Resistance measurements; +/-1% on 50Ω and 50MΩ Resistances measurements
• Resolution: 5 1/2 Digit
• Floating COM with on board isolated power supply
• Protections:
  • 60V PTC for Voltage and resistances and uA
  • 630mA fuse for mA rail
  • 6.3A fuse for A rail

• Communication: Custom SPI protocol

DMM Shield is powered by the system board. It uses both 5V0 and 3V3 power supplies. The average consumption of the DMM Shield is 90mA. The DMM shield features on-board power supplies that are used to power the DMM core of the board. The 5V power supply is isolated in order to provide an isolated reference signal for measurements. There are more than one reference signals on the DMM Shield board:

• GND- Ground for the non-isolated section. References all the signals and voltage rails in the non-isolated section such as 5V0 and 3V3 voltages from the system board, relay driver, flash memory
• VSS_ISO - Most negative voltage in the isolated section. It is the reference for isolated power supplies VCC5V0_ISO and VCC3V3_ISO as well for all the digital signals in the isolated section
• COM_ISO - Reference for the DMM measurement. All the measurements done with the DMM Shield will be referenced to COM_ISO signal, through COM connector, J2. The reference is leveled at 1.8V above VSS_ISO
• AGND_ISO - Reference for all the analog signals in the isolated section. It is connected to the COM_ISO through a 0Ω resistor

The DMM Shield is equipped with the Arduino shield header that provides powering and communication between the DMM Sheild and system board. There are also 4 banana connectors that interface the DMM with the sources and devices that need to be measured.

Banana Connectors (J1-J4)

• J1 (V/Ω)- is used for measuring the AC/DC voltages, Resistances, Diode and Continuity.
• J2 (COM)- is the reference for all the measurements that can be done with the DMM Shield. COM signal is floating from all the other reference points from the board.
• J3 (500mA)- is used for measuring AC/DC currents up to 500mA.
• J4 (5A)- is used for measuring AC/DC currents up to 5A.

Arduino Shield Connector (J5-J9):

• J5 - 1×2 Header- Digital pins
• J6 - 2×6 Header- Analog pins
• J7, J8 - 2×8 Headers- Digital pins
• J9 - 1×8 Header- Power pins
• For detailed usage of each pin please see the Pinout Table AppendixPinout Table Appendix.

Jumpers:

• JP1- Frequency Measurement -Not Implemented

SPI Pins

The DMM Shield supports SPI communication with both the DMM chip and theEEPROMchip. The hardware interface lines DataIn (DI), DataOut (DO) and Clock (CK) are shared between the two devices, and the Chip Select (CS) lines are separate, allowing the user to access either of them with fewer hardware resources used.
The DMM chip is electrically separated from the rest of the circuitry, therefore the communication lines need to be isolated as well. TheEEPROMCSline is active high, while the DMMCSline is active low. The reading sequence for SPI DMM communication is the one below:The writing sequence for SPI DMM communication is the one below:The timing for SPI DMM communication is the one below:

GPIOPins

There are threeGPIOpins used for Relay control: RLU, RLD, RLI. Depending on the type of measurement performed, the corresponding relay/s need to be triggered/commanded using aGPIOpin. The relays RLI, RLU, and RLD are controlled by three digital signals, IO2, IO3, and IO4, from the shield connector.

In addition to configuring theGPIOpins, setting each scale assumes the configuration of some registers. The HY3131 chip provides 23 configurable registers.

For more information please see the library documentation for each platformZYNQorDigilent Microcontroller boards.

The DMM Shield is equipped with a non-volatileEEPROMmemory chip from Microchip: 93LC66BTdatasheetavailable from Microchip's website ), which has 512 bytes/256 words (4kbits) available space. The memory can be accessed over a custom SPI protocol, using digital IO pins exposed in the DMM Shield connector:CS_EEPROM(EEPROMSPI chip select), DO (SPIMISO), DI (SPIMOSI) and CLK (SPI CLK).

While the chip select line is specific toEEPROMmodule, the SPI lines (data and clock) are shared with the DMM device.

Note the data is written and read from memory using word format addressing, instead of byte: bytes 0-1 are written at address 0x00, bytes 2-3 are written at address 0x01, etc.

TheEEPROMis used to store the following system information:

Please consult the DMM Shield Library User Guide for more information about theEEPROMmodule usage and communication. For more details about Calibration process, read more onCalibration Procedurebelow.

DMM Shield comes with preset scales of measurement. They will indicate the maximum value that can be accurately measured with the device. Keep in mind that at low values the resolution is lower and different scales might give a more accurate result since the device is calibrated closer that value. Ex: for a 40kΩ resistor is better to use the 50kΩ scale instead of the 500kΩ for a better resolution. There are 4 scales for voltages, 5 for current and 7 for resistances. Additionally, there are two extra scales for Diode and Continuity.

The device comes factory calibrated for each scale. For more details about calibration please see theCalibration procedurebelow.

数字的准确性盾是0.1%左右AC/DC Currents and Voltages, 500Ω-5MΩ Resistances and within the scales; 1% for 50Ω and 50MΩ Resistances.For AC Current and Voltage we guarantee the 0.1% accuracy at 50/60Hz. Note that outrunning the end of a scale will increase the measurement error. The accuracy is computed in percentage as a difference between the reference value and the measured value, reported to full scale.

让我们考虑美元R_ {F}, M_ {F}作为参考和美元the measured value at full scale and $F_{S}$ the full scale. The accuracy is computed as follows:

$$Accuracy=\frac {R_{F} - M_{F}}{F_{S}} * 100\label{10}\tag{10}$$

The DMMShield needs calibration before performing measurements and delivering correctly measured values to the user. This is due to errors introduced by the chip itself and on-board additional electronics. Calibration is the process of computing and applying correction coefficients to the measured values that allow precise measurements.

The process consists of computing an additive and a multiplicative coefficient for each scale.

Calibration is done by collecting pairs of reference value and measured value (RefVal, MsVal) in multiple points. The reference value is the value measured with an accurate instrument, considered to be the actual value to be measured by the DMMShield device. The measured value is the value reported by DMMShield hardware. When all these pairs are collected, the calibration coefficients are computed mainly using the difference between the reference and the measured values.

Depending on the scale, different types of calibration are performed, as detailed in the following chapters:

This method applies to the Resistance scales. It collects the pairs (RefVal, MsVal) in two points: 0 point (short between probes), and full scale value.

Let’s consider this pairs as being ($R_{0}$, $M_{0}$) and ($R_{F}$, $M_{F}$). The calibration coefficients are computed in the following manner:

$$Calib_{MULT}=\frac {R_{0} - R_{F}}{M_{0} - M_{F}} - 1\label{1}\tag{1}$$ $$Calib_{ADD}=(R_{0} - M_{0})(1 + Calib_{MULT})\label{2}\tag{2}$$

The reference value for the short is considered to be 0: $R_{0} = 0$

The calibration coefficients are applied to the acquired value in the following manner: $$Value_{corrected}=(1 + Calib_{MULT})Value_{acquired} + Calib_{ADD}\label{3}\tag{3}$$

This method applies to the DC Voltage and DC Current scales. It collects the pairs (RefVal, MsVal) in three points: 0 point (short between probes for voltage and open for current), negative full scale value and positive full scale value. For example, for VoltageDC500m scale, the following points are used: 0 point (short between probes), -500mV, 500 mV.

Let’s consider this pairs as being ($R_{0}$, $M_{0}$), ($R_{FN}$, $M_{FN}$) and ($R_{FP}$, $M_{FP}$). The calibration coefficients are computed in the following manner:

$$Calib_{MULT}=\frac {R_{FP} - R_{FN}}{M_{FP} - M_{FN}} - 1\label{4}\tag{4}$$ $$Calib_{ADD}=(R_{0} - M_{0})(1 + Calib_{MULT})\label{5}\tag{5}$$

The reference value for the zero calibration is considered to be 0: $R_{0} = 0$

The calibration coefficients are applied to the acquired value in the following manner: $$Value_{corrected}=(1 + Calib_{MULT})Value_{acquired} + Calib_{ADD}\label{6}\tag{6}$$

This method applies to the AC Voltage and AC Current scales. It collects the pairs (RefVal, MsVal) in two points: 0 point (short between probes for voltage and open for current) and full scale value. For example, for VoltageAC500m scale, the following points are used: 0 point (short between probes) and 500 mV.

Let’s consider this pairs as being ($R_{0}$, $M_{0}$), ($R_{F}$, $M_{F}$). The calibration coefficients are computed in the following manner: $$Calib_{MULT}=\frac {R_{F}}{\sqrt{{M_{F}}^2 - {M_{0}}^2}} - 1\label{7}\tag{7}$$ $$Calib_{ADD}= M_{0}\label{8}\tag{8}$$

The reference value for the zero calibration is considered to be 0: $R_{0} = 0$

The calibration coefficients are applied to the acquired value in the following manner: $$Value_{corrected}=(1 + Calib_{MULT})\sqrt{| {Value_{acquired}}^2- {Calib_{ADD}}^2 |}\label{9}\tag{9}$$

Digilent provides libraries to access DMM Shield functionality. The libraries were created to support ZYNQ plaform and Digilent PIC32 microcontroller boards. Both libraries come with a demo that allows the communication with the DMM Shield through UART. Functions as setting a scale and measure can be accessed by entering commands in the UART terminal emulator. Another demo shows how to access the memory left in theEEPROMby reading and writing 32 words. Documentation and downloads for these libraries can be found at the following locations:

• ZYNQ
• PIC32
• Arduino

This reference manual applies to Revision C of the DMM Shield.

• Arduino DMM Shield Library User Guide
• Arty Z7 DMM Shield Oled Demo User Guide
• Arty Z7-20 DMM Shield Webserver Demo User Guide
• PIC32 DMM Shield Library User Guide
• Zynq DMM Shield Library User Guide